Samsung idcs 28d user manual

You must have a PARK button or park access code to retrieve and place calls in park orbits. If the parked call is not retrieved within a pre-programmed period of time, it will recall your keyset and have a slow flashing amber light.

You cannot park and page intercom calls. Dial the desired zone number. After the attention tone, instruct the paged person to dial Remain off-hook until the person dials 56 from any phone. The paged person will be automatically connected with you.

While in conversation, press the PAGE button. The call is automatically parked at your station. Receive page tone and dial a desired page zone number. Make announcement indicating your extension number or the line number. Hang up. If you have a PARK key, press it and dial the announced orbit number. If the call is not retrieved within a pre-programmed period of time, it will recall your keyset and have a slow flashing amber light. Standard telephones receive special dial tone as a message indication or a lit message lamp, if the phone is equipped with one and they are connected to an 8MWSLI card or a 16MWSLI card on the system.

A station can have up to five message indications. Display keyset users can view message indications and return them in any order. If a message has been left at your keyset by a keyset in Auto Answer, you must manually cancel the message after it has been returned. Display stations calling you will see this message and be informed of your status or follow your instructions. To cancel any of these messages you might have selected, dial 48 plus The message is set and the button will light red.

Press the button again to turn off. Pressing another programmed message PMSG button will turn the previous one off and set a different programmed message.

To cancel all message indications left at your keyset, dial 42 plus your extension. The first station that left a message will be called automatically.

Repeat until all messages have been returned in the order received. The DND key lights steady red to remind you of this mode.

The DND light turns off. You can make calls while in the DND mode. The single line extension on your modem will be disconnected.

You can set up to three alarms. If you are on a call and you do not wish to be interrupted while on that call, you can press the DND key and place your station in Do Not Disturb. When you hang up at the end of the call, DND will be automatically canceled and your keyset will be able to receive new calls. This feature requires a DND key. When the alarm rings, you will hear three short rings repeated three times.

Lift the handset to answer the alarm. If you do not, the alarm will alert you two more times at five minute intervals. It will light red. To resume speaking, press the MUTE button again. The light turns off. Dial the alarm number 1, 2 or 3. Dial the time at which you want the alarm to sound. Enter the time as HHMM hours and minutes using the 24 hour clock.

Repeat for each alarm if needed. Press the HOLD button again to turn music off. Dial alarm number 1, 2 or 3. NOTE: Display keysets can show a reminder message. This does not affect the speakerphone level. You are connected to the door phone. If an electric door lock release is installed, dial 13 to unlock the door.

The microphone is not in use, so the distant party does not hear other parties present in your office. Repeat if necessary. You may call the door phone and listen to what may be happening outside or in another room. NOTE: Depending on speaker volume and the acoustics of your office, it may be advisable to turn the group listening feature off before hanging up. This will eliminate a momentary squeal.

You will be connected to the door phone and you can listen or have a conversation. When the executive station is in the DND mode, all of its calls will ring the secretary station. Using the hot line will override DND at the other station. This key will light red when the other station is in use. Press the ACCT key again. Your conversation will not be interrupted. Only the last account code dialed will be printed.

You can unlock it when you return. Your default station passcode is Dial your four digit station passcode. Dial 1 to locking outgoing, 2 for locked all calls, or 0 to unlock. You may press the MS key repeatedly to send multiple signals to the designated station. If you are using the speakerphone the announcement will always be heard through the speaker. When you receive a busy signal, press the OHVA key. After the attention tone, begin speaking. Press the flashing CALL button on your keyset.

This will place the original party on hold and allow you to talk to the announcing party. To return to your first party, press the key corresponding to your original call. This will disconnect the OHVA call. When you are voice announcing to a station close to you, use the handset to avoid an echo effect.

You cannot off-hook voice announce to single line telephones. Use caution because the conversation through the AOM may possibly be heard by the caller on the keyset. Executive off-hook voice announce can only be accomplished when an AOM is attached to your phone.

The calling station must have an OHVA key. The OHVA feature will work with intercom and transferred calls. Pressing this key will prevent anyone from making an OHVA to you until you press the button again and cancel the blocking. Pressing this key while receiving an OHVA call will disconnect the voice announcing party and return you to your original call.

While you are out of the group, you can receive calls to your extension number but not calls to the group number. It will light red when your keyset is in the group. Repeat as necessary. A BGM source must be selected for this to work.

This feature allows people using the AME feature to enable password protection. This will prevent unauthorized people from listening to your messages being left.

The passcode is the same as your station passcode. This means that if you are in multiple groups, you can decide for which groups you will receive calls. NOTE: Specific lines or stations may be programmed to ring with a different tone than what you have selected for your keyset. You can change your station passcode whenever you desire. Dial your old passcode. Dial a new passcode must be four characters. You can use 0—9. Redial the new passcode to verify. If successful, you will hear two beeps.

Four beeps indicate an incorrect code. Reenter the code again. This feature can be turned on or off at your keyset. Dial to turn Automatic Hold on or to turn it off. Dial to use the headset or to use the handset. Your keyset may be equipped with a Headset mode key. If it is so equipped pressing this key while the light is out will cause the keyset to enter headset mode and the light will illuminate to indicate this. Pressing the key while the light is lit will cause the keyset to return to handset mode and the light will go out.

Calls can be made and features activated by simply dialing the C. Dial to turn the Hot Keypad on or to turn it off. This tone can be turned on or off. Dial to turn tones off or to turn tones on. Dial to turn this feature on or to turn it off. This method will always answer calls in the order they arrived at your keyset. When you turn ring preference off, you must press the flashing button to answer a call, allowing you to answer calls in the order you choose.

This list can be from ten to fifty calls in a first in, first out basis. If to this station. If an option is not authorized, please speak to your system Administrator. Samsung Voicemail Services Menu This manual is also suitable for: Telco idcs 28d. Print page 1 Print document 8 pages. Rename the bookmark. Delete bookmark?

Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Samsung Telephone DS 24D. I need to access the voicemail messages on a past. Samsung Telephone idcs 28D. We recently moved to an office with an existing ph. However, support for these products with refurbished equipment and The Samsung iDCSD phone is ideal for the established company whose business is telephone intense. From the receptionist to the busy executive, this keyset does it all.

Instructions are detailed and easy to follow. Where a feature is specific to one of the systems above it will be clearly identified otherwise all features are applicable to all DCS systems. When assistance is needed, contact your Samsung Communications Specialist.

If you are not sure what Samsung DCS phone will work on your system, please feel free to ask. All manuals on ManualsCat. Phone and Voicemail. Also for: Telco idcs 28d. Please see your system ad- ministrator to determine the number of bins assigned to your keyset. The 64 button module is used when you need more programmable keys 2. First time users should read this section as a tutorial. The main things to should do are: greeting will answer.

Sender information is not available on outside calls. This is useful if you are frequently traveling or changing the Send a Copy to Someone Else number where you can be reached. Save the Recording When Follow Me is activated, the transfer will be supervised. The first five of these automatically before each message. If this is disabled, the information are used in the 'Find Me' feature, but any of them can be easily dialed must be requested manually by pressing '00'.

They This menu allows you to make changes, that are rarely changed. Use these require setup by the System Administrator. You probably will not need them after that. This will prevent unauthorized people from listening to messages being left for you. Calling a station that is busy or does not answer you can press [ ] to immediately send the call to the called parties mailbox.

This manual is also suitable for: Idcs 18d Idcs 8d Idcs 64b Idcs 14b. Print page 1 Print document 44 pages. Rename the bookmark.